32 archived Australian notices, each linked to its official Product Safety Australia source. The page updates automatically when new notices arrive.
The car seat adapter set may fail to engage and connect properly with the spring-loaded pin on the Joolz Aer2 stroller. During use, the product can cause the car seat to detach from the stroller, tip forward and fall to the ground. This can occur even when the adapter appears to be locked in place.
This product does not comply with the mandatory standard for child restraints for use in motor vehicles .
This product does not comply with the mandatory standard for child restraints for use in motor vehicles .
These products do not comply with the mandatory standard for child restraints for use in motor vehicles .
These seat belt adjusters may interfere with the normal operation of the seat belt and reduce its effectiveness.
This product does not comply with the mandatory standard for child restraints for use in motor vehicles .
These seatbelt adjuster clamps may interfere with the normal operation of the seat belt and reduce its effectiveness.
This product may interfere with the normal operation of the seat belt and reduce its effectiveness.
This product does not comply with the mandatory standard for child restraints for use in motor vehicles .
The product does not comply with the mandatory safety standard for child restraints for use in motor vehicles.
Car seat head straps can increase the risk of spinal cord injury or death by altering head and neck alignment during a crash. They may also pose a suffocation or strangulation risk if they slip around the child’s mouth or neck. These products are the subject of a safety warning notice .
The product does not comply with the mandatory safety standard for child restraints for use in motor vehicles .
The product does not comply with the mandatory safety standard for child restraints for use in motor vehicles .
The product does not comply with the mandatory safety standard for child restraints for use in motor vehicles.
The product does not meet the requirements of the mandatory standard 'Consumer Protection Notice No. 3 of 2014 - Child restraint systems for use in motor vehicles'. The product does not have the correct safety warning label.
The seat buckle screws may become loose or separate and prevent the buckle from securing properly.
The product does not meet the requirements of the mandatory standard 'Consumer Protection Notice No. 3 of 2014 - Child restraint systems for use in motor vehicles'. The buckle screws may become loose and prevent the buckle from securing properly.
Testing of the product has identified safety concerns. In the event of an accident, the harness anchor point may detach from the frame of the car seat.
The top tether strap may release under excessive load.
The product does not comply with numerous user instructions and labelling requirements under the mandatory standard Consumer Protection Notice No.3 of 2014, Safety Standard: Child restraint systems for use in motor vehicles.
The product does not comply with numerous user instructions and labelling requirements under the mandatory standard Consumer Protection Notice No.3 of 2014, Safety Standard: Child restraint systems for use in motor vehicles.
The product does not comply with numerous user instructions and labelling requirements under the mandatory standard 'Consumer Protection Notice No.3 of 2014, Safety Standard: Child restraint systems for use in motor vehicles'.
The product does not comply with labelling, branding and user instruction requirements of the Australian Standard AS/NZS 1754.
The product does not comply with labelling, branding and user instruction requirements of the Australian Standard AS/NZS 1754.
The product is only a half booster design with insufficent back support that does not meet Australian Standards.
In some instances, the fabric around the harness adjuster mechanism may get caught in the mechanism, allowing the shoulder harnesses to loosen without lifting the harness adjuster. In addition, the A4 model does not have the correct certification.
In some instances, the fabric around the harness adjuster mechanism may get caught in the mechanism, allowing the shoulder harnesses to loosen without lifting the harness adjuster.
The side panel of the seat cover does not come apart to allow the airbag to deploy correctly.
The metal snap hook on the Tether Extension strap may deform under load (as may be experienced in a collision). This is due to incorrect hardening of the metal parts.
The metal connecting hooks at either end of the Hemco Adjustable Tether Strap may deform or break under load stress (as may be experienced in a collision). This is due to inadequate heat tempering/hardening of the metal parts.
Under certain conditions, the TS26 adaptors may break or crack on impact, causing the infant car seat to dislodge or fall from the stroller.
The car seat adaptor support bars can fail, posing a fall hazard to children.